EV805A-A Discover 深循环 8V 235AH 工业电池 价格及参数

Discover® DRY CELL Traction Industrial batteries outperform traditional Flooded, AGM, and Gel deep-cycle batteries in demanding traction and industrial applications. The batteries are designed to deliver a long runtime, high operating current and withstand deep discharge and are ideal for powering e that is used multiple times a day.

DRY CELL Traction Industrial batteries have been used and trusted for more than ten years by the world’s largest industrial Original E Manufacturers. Specific charge algorithms are available that support optimal battery performance and longevity.

NOTE 1: Dimensions have a ±2 mm (0.08 in) tolerance. Weights may vary.
NOTE 2: Refer to terminal guide on website for torque values.

NOTE 3: Extra considerations must be given when designing systems for use at maximum temperatures.
NOTE 4: Internal Resistance is approximate.

3 HR: 1.70VPC; 5 HR: 1.75VPC; 20 HR: 1.80VPC. All at 25°C/77°F

HYDRO POLYMER

Organic capillary separators with hydro polymer electrolytes resist dry-out and prevent thermal runaway

Maintains performance characteristics over operational life

ENHANCED ALLOYS

Thick plates with graphite enhanced alloys deliver maximum runtime over operational life

CARBON BOOST

Carbon additives to increase duty cycle performance, charge acceptance and partial state of charge operation

AUTOMATED THROUGH-THE-PARTITION WELD

Improved intercell weld consistency, and less lead waste than manual welding process (key models)

Supports higher current loads and lowers internal resistance

POLYPROPYLENE CASE

High heat resistance and durability (key industry models)

High precision pressure relief valves reduce water loss and extend life

Integrated flame arrestors prevent fire and explosion

ENHANCED RUNTIME

High amp hour capacity

High operational voltage over lifetime

Delivers 80% DoD above 1.9 VPC

EXTENDED SERVICE LIFE

Long life superior to deep-cycle FLA / AGM / Gel batteries

550+ cycles 70% DoD (IEC 254-1 Traction Lead-Acid)

350+ cycles  DoD (DIN 43 539 VRLA)

RESILIENCE

Partial stage of charge operation superior to AGM

Intense duty cycling superior to AGM / Gel

Overcharge and over-discharge resilience superior to AGM

Compatible with AGM / Gel semi-traction charge profile

EXTREME TEMPERATURES

High temperature life superior to AGM

Low temperature operation superior to FLA / AGM / Gel batteries

EXTREME VIBRATION RESISTANCE

Vibration resistance superior to AGM / Gel

Shock tested (IEC 61373, DIN EN 61373, SAE J537)

OEM TRUSTED

Exceeds OEM specifications

Innovative technology

Global service and support

RELIABLE AND SAFE

Valve Regulated Lead-Acid, Dry Cell AGM

Maintenance-free, nonspillable, no-gassing

Spark and explosion tested (SAE J1495)

UALITY

Discover® manufacturing facilities are fully certified to ISO 9001/14001 and OSHA 18001 standards.

Designed in accordance with and published in compliance with applicable standards, including:

IEC 60254-1. Lead-Acid Traction

DIN 43 539. VRLA

SAE J537. Storage

UL, CE Health Safety Certified

Classified as a nonspillable battery

Without restriction for transport by Sea (IMDG amendment 27)

Without restriction for transport by Air (IATA/ICAO provision 67)

Without restriction for transport by Ground (STB, DOT-CFR-HMR49)

Due to self-discharge characteristics of lead-acid battery technologies, batteries should be top charged within 6 months of storage to ensure optimum performance, prevent sulphation and permanent capacity loss.

Charge profile recommendations correspond to battery voltages at 25°C (77°F). For temperatures below, adjust +5mVPC/°C (+3mVPC/°F). Temperatures above, adjust -5mVPC/°C (-3mVPC/°F). Temperature compensated charging helps ensure optimum battery runtime and life performance.

Charge profile recommendations depend on application and charger. IUI (or IUI with Pulse) is appropriate for applications that require frequent and deep discharges. IUU is appropriate for applications that are on standby and cycled less frequently.

IUI with Pulse algorithm uses a pulse termination criterion. The finish current is pulsed on and off in order to keep the battery voltage at a minimum while still reaching target overcharge. If average VPC exceeds U4 and the charger output has been on for more than 30 seconds, the output is shut off until VPC falls to U3.

IUI Charge Profile (if applicable), may have a continuous float phase added (2.27VPC).